etrailer | Trailer Wiring Harness Installation - 2014 Ford Focus

Описание: Click for more info and reviews of this CURT Custom Fit Vehicle Wiring:
https://www.etrailer.com/Custom-Fit-V...
Check out some similar Custom Fit Vehicle Wiring options:
https://www.etrailer.com/fitguidet1.htm

Search for other popular Ford Focus parts and accessories:
https://www.etrailer.com/vehicle/2014...

https://www.etrailer.com
Don’t forget to subscribe!
   / etrailertv  

Full transcript: https://www.etrailer.com/tv-install-t...
Today on our 2014 Ford Focus sedan, we'll be installing the Curt key connector vehicle wiring harness for forward pull flat trailer connector, part number C56138. Now we want to use our wire to hook up to our trailer. We can just set it aside here to the side of our latch of our trunk. Close our trunk on down and we have plenty of wire to make our connection to our trailer. And now when we're not towing our trailer, we can stow it out of the way inside of our trunk. Just open up our spare tire cover here, drop it on inside, close it on up, it's out of the way.

It's not going to get snagged on any of our cargo and we're not going to cause any damage to it that way. We can start our installation by opening our trunk. Remove all of our floor liner, covers up our spare tire and we'll set that aside. Remove the foam that goes around our spare tire as well. It's two pieces, just pull it on out. Now remove our center trim panel piece here.

There's two clips that hold it in place. You can use a flat head screw driver or a trim panel tool to get behind those clips. They pull right out. So either a trim panel tool or a flat head screw driver and come up on our panel here to help assist it in coming up. Now both of our corner panel pieces have one more of those panel fasteners on them. Remove that and we'll work our panel off.

We'll do the same on our passenger side. Now we'll remove this panel clip here that holds our carpet in place. You have one of these on both sides of the vehicle. Get that out of the way. We can pull our carpet and do the same on the other side. Okay now we're going to start on the left side of our vehicle.

Right here we have an electrical connector. This electrical connector here goes to our driver side taillight. Push in on this tab here, pull back to separate it. We'll grab our pair of wires that has the yellow wire in it. This is for our left side turn signal. This brown wire here is for our tail light. So I will plug it in mine with the wire harness that we just disconnected. Push it in until it clips. The other end goes back into the vehicle here. Push that in until it clips. This green and red wire, this controls our passenger side or our right side turn signal and our brake light. We'll just run it over to the passenger side of the vehicle. Unplug our connector here, make our connections. All right. Now we have our control box here. We'll take our included double sided tape, peel off one side, place the tape on, press down firmly and mount this to a good solid flat surface inside our vehicle where it's tucked up out of the way. Right here on this auxiliary fuse box in our trunk on the side would be a great spot for that. Peel the other end off and place it on there. Press it on nice and firmly. Okay now we need to ground our converter box here. We use the provided self tapping screw that comes in our kit or we can it on a ground that already exists on our vehicle. We have on right here. So to avoid drilling any holes, we'll use that one. It's an eight millimeter screw. Take the bolt out. Put the bolt over our wire and reinstall the bolt. Snug it back down. Okay, that'll give us a perfect and solid ground for our box. Now our black wire coming off our converter box, we'll strip a little bit more of the insulation off. Right there will be fine. Take one of the yellow butt connectors that comes in our kit, place it over the black wire for our converter box and we'll crimp it down. This black wire is our power wire that will run to the front and connect to our vehicle's battery. Take the black wire that comes with our kit, strip off a little bit more of the insulation from it and now we'll connect our two wires. And with that crimped, we'll pull back and make sure it's all secured. I'll wrap it up with some electrical tape just to help protect in case dirt we're to enter our vehicle from the trunk or potentially the trunk has a leak at some point in time, we don't want to get any water in there and cause corrosion or a short. Now this grommet right here, right below our fuse box in the trunk. We'll take this out here real quick. This we're going to pass our power wire down through. We'll make a notch in our grommet here and another diagonal notch right there give our wire a place to rest. And we'll drop our power wire on down through this hole. Okay we have our wire passed through all the way, we'll slide our grommet around it and reinstal