DIY Door Boot Seal Replacement for Electrolux Washer

Описание: 🔧 How to Replace the Door Boot Seal on a Front-Load Electrolux Washer (Step-by-Step DIY)

Does your front-load washing machine smell like mold or mildew?
Chances are your door boot seal (rubber gasket) is the culprit.

In this video, I walk you through exactly how to remove and replace the boot seal on a front-load Electrolux washer, step-by-step — even if you’ve never done appliance repair before.

This seal can trap moisture, soap residue, and mildew over time, causing that nasty smell that just won’t go away. Replacing it is easier than you think and can save you hundreds of dollars vs. a service call.

What you’ll learn:

✔ Tools you need
✔ How to safely unplug & disassemble the washer
✔ Removing the retaining spring and old boot
✔ Correct boot alignment (triangle markers & knobs)
✔ Reinstalling hoses, weights, and panels
✔ Tips to prevent mold buildup in the future

Tools used:

• Needle-nose pliers
• Phillips or square bit screwdriver
• 7/16" socket
• Zip ties
• Replacement boot seal

👉 I also share a simple cleaning habit that keeps this from happening again.

If this helped you, hit Subscribe for more practical DIY fixes, home repairs, and money-saving projects.

Here are the step-by-step instructions:
1. Unplug the power cord from the wall
2. Move washer away from the wall
3. Use Phillips head screw driver to remove the 2 screws in the back holding the top on and remove top panel
4. Keep track of which screws go where
5. Notice where the arrows on the boot seal line up with the arrows on the washer front panel. You will. Need to line the new one up exactly the same way. Maybe take a photo of it so you will remember just exactly how it should go on.
6. Use needle nose pliers to remove the retaining ring from front panel
7. Peel the boot seal off of the front panel
8. Remove screws under the front panel Should be 4 screws. (So we are at 6 screws now)
9. Pull out the dispenser drawer and depress the tab to fully release it
10. Remove the 2 screws from the dispenser drawer housing.
11. Remove 3 screws holding the top of the front panel
12. Lift front panel up and pull it off
13. Disconnect the 2 wires connected to the front panel
14. Remove the lower counter balance weight with a 7/16” socket. 4 bolts.
15. Remove light assembly from the boot seal
16. Remove the two hoses after cutting the zip ties
17. Remove retaining spring from outer tub.
18. Notice where the triangle tabs line up on the tub
19. Remove the upper counter balance weight
20. Install new boot seal by first aligning the top triangles
21. Reinstall the retaining spring on the boot seal. Use clamps or another pair of hands to help hold the spring in place while you install it.
22. Insert tubes back into their ports. Secure them with new zip ties.
23. Insert light into receptacle hole
24. Reinstall the counterbalance weights with the mounting bolts
25. Reinstall the front panel by connecting the two wires and align the panel on the mounting pins at top and push down into place
26. Reinstall the 3 screws on top
27. Replace the 2 screws in the dispenser drawer housing
28. Reinstall the dispenser drawer
29. Reinstall the 4 screws at the bottom of the front panel
30. Align the boot seal on front of panel – be sure the arrows line up
31. Reinstall the retaining wire with the spring at the top of the boot seal
32. Reinstall the top panel and secure the 2 screws at the back of the panel.
33. Push washer back against the wall and plug it in.
34. Now the job is done and you can start washing clothes again.
35. It’s a good idea to wipe out the rubber boot seal on a regular basis to keep it from getting mold and mildew build up.