Volvo XC60 2.0L D4 Diesel Engine Oil & Filter Replacement - How to Step by Step Guide 2018 Onwards

Описание: The following EveryDay Workshop video explains Step by Step the procedure to carry out an engine oil and filter change on a 2019 Volvo XC60 2.0L D4

The procedure should also be the similar on most Volvo 5 cylinder engined cars.

The tools, parts and steps to help you carry out this task are also listed below. And if you have any questions please let me know in the comments.

⚙️ We upload How To videos as well as other interesting topics regularly. Hopefully these will save you time and money. If you have enjoyed or found any of our videos useful, we would love you to give us a 👍 and consider subscribing to our channel. Thank you

If we have do a good enough job with this video and you would like to buy us a ☕️ or 🙂 maybe a 🍺 : https://www.buymeacoffee.com/Everyday...

————————————————————

🛠 PARTS USED IN THIS VIDEO 🛠

➡ Service kit: https://ebay.us/fjYAQw

➡ 5 Litres Mannol SAE 0W-20 Fully Synthetic Engine Oil: https://ebay.us/lMuX1b

➡ The specific service kit I use for the vehicle in the video can be purchased from the following link: https://ebay.us/Wua7pD

➡ 86mm Oil filter housing removal socket: https://ebay.us/G7rs12

➡ Replacement Service Booklet: https://ebay.us/2B6Aqd

These are affiliate links so I will receive a small commission at No extra cost to you.

Note: Please make sure you order the parts for your specific vehicle. These links may not be correct for your vehicle, but you should find the correct ones from these suppliers.

——————————————————

Chapters:

0:00 - Introduction
0:20 - Removing undertray
1:10 - Draining the engine oil
1:50 - Removing the oil filter housing and renewing the filter
3:10 - Refitting the sump drain plug
7:15 - Refitting the oil filter housing
8:05 - Filling the engine with new oil
9:10 - Starting the engine and checking for leaks and level

——————————————————

🛠 Tools and parts required: 🛠

1 - T30 Torx or 12mm socket for the sump gaurd
2 - 36mm socket for oil filter housing - 17mm socket for sump drain plug
4 -Torque wrench
5 - Container large enough to hold all the old oil
6 - New oil filter
7 - 5.9 litres of oil (Check the recomendation for your model - engine - country)8 - Oil drain plug washer
9 - Means to raise the vehicle safely to allow access. ie Ramps - Jack - Axle stands

——————————————————

Procedure:

1. Run the engine until at normal operating temperature.

2. Raise the front of the car. Be sure that it is secure.

3. Remove the engine under tray (T30 torx drive). These may be different on some vehicles.

4. Position a container under the engine alligned with the oil drain plug.

5. Remove the oil drain plug (17mm socket) and drain the engine oil (the oil will be HOT)

6. While oil is draining, use a 36mm socket and remove the oil filter housing.

7. Remove the old oil filter, clean the housing and replace the o-ring.Lubricating the new O-ring with oil. Fit the new filter and reinstall the housing (Tighten to 25nm).

8. Reinstall the oil drain (with a new one if supplied) and tighten it to 35 Nm. Always use a new sealing washer.

9. Fill the engine with the new oil specified for your vehicle. (The oil for this particular vehicle is: SAE OW-20 Fully synthetic and the make of oil is Mannol Legend Ultra) (Please see the above links to purchase this oil and service kit) Check the level on the dipstick or electronic display and top up to the required level.

10. Start the engine and check for oil leaks around the oil filter housing and the oil drain plug. When on level ground re-check the oil level and top up if needed, but do not overfill.

11. Reinstall the under tray.

——————————————————

Thanks again for watching and I hope you found this video useful.

#Oilchange #Volvo #DIY