Service - V3 Dropper Travel Pin Adjustment

Описание: TRAVEL ADJUSTMENT INSTRUCTIONS

Things You Will Need
10 Travel pins (included with dropper)
Slickoleum (included with dropper)
Strap wrench (for collar if beyond hand tight)
Lint free cloth

Assembly time is approximately 10 minutes. Difficulty: Easy.
Drop tuning can be done on-bike, almost tool free and without removing the saddle or touching a shock pump. Lowering the post travel also increases bushing overlap and guide pin length, which is great for heavier riders.

240mm Dropper Post - adjustable down to 220mm
210mm Dropper Post - adjustable down to 190mm
180mm Dropper Post - adjustable down to 160mm
150mm Dropper Post - adjustable down to 130mm
120mm Dropper Post - adjustable down to 100mm
90mm Dropper Post - adjustable down to 70mm

STEP 1: COMPRESS DROPPER
Press the remote lever and compress the dropper to roughly mid travel.

STEP 2: MID CAP ASSEMBLY
Unscrew the mid cap assembly (8,9) by hand or with your strap wrench if necessary. Slide it up towards the seatpost head.
Press the remote lever to extend the post & to pop the upper bushing (10) out of the lower post. Then slide the bushing up towards the seatpost head.

STEP 3: INSTALL TRAVEL SHIM PINS
Once the mid cap assembly (8,9) & upper bushing (10) are out of the way you should have clear access to the 5 travel adjustment channels.
For 10mm travel reduction: Install the first 5 10mm travel pins (18) by sliding 1 pin per slot into the guide slots of the upper tube (1).
For 20mm travel reduction: Once the first 5 10mm travel pins are in place, using your finger, gently push each travel pin down the guide slot until you can fit the next 5 10mm travel pins.

STEP 4: COMPRESS DROPPER
Once the travel pins (18) are in their respective guide slots, push the remote lever and slowly drop the post to mid travel. This action should be smooth. If it requires force or feels rough, stop and double check the travel pins are seated correctly before proceeding.

STEP 5: GREASE & INSTALL UPPER BUSHING
Grease the upper bushing (10), inside and out, with your light suspension grease. You can also apply some grease to the upper tube (1) just above the lower tube (13). Slide the upper bushing back over the upper tube. You can now seat the upper bushing into the lower tube by pushing down on it with your thumb and index finger. It should look like the photo below.
NOTE: When the mid cap assembly is unthreaded from the lower tube, the dropper can extend further than the functional max length. Make sure to compress the dropper to mid travel before attempting to thread the mid cap assembly back onto the lower tube.

STEP 6: TIGHTEN MIDCAP ASSEMBLY
With the upper bushing (10) fully seated in the lower tube (13), you can now slide the mid cap assembly (8,9) down and thread it to the lower tube by hand. Once it is hand tight it is recommended you snug it up with a strap wrench.

STEP 7: FUNCTION CHECK
Cycle the post a couple times to confirm smooth action. If excess grease builds up on the dust wiper (9), wipe it away with your cloth. If there is more grease than necessary, it will weep out through the dust wiper after some cycling. This is normal. If you do notice any excess grease on the dust wiper be sure to wipe it away so it doesn't attract unwanted grit. This weeping of excess grease should only last a ride or two.

If you are having any problems please first double check that you have correctly completed each of the above steps.
If you are still having trouble please email us at [email protected] for help.

TIMESTAMPS
00:00 Tools Needed
00:38 STEP 1: COMPRESS DROPPER & LOOSEN MID CAP ASSEMBLY
00:43 STEP 2: MID CAP ASSEMBLY
00:59 STEP 3: INSTAL TRAVEL PINS
01:46 STEP 4: GREASE AND INSTAL UPPER BUSHING
02:25 STEP 5: COMPRESS DROPPER
02:42 STEP 6: TIGHTEN MID CAP ASSEMBLY
02:42 STEP 6: FUNCTION CHECK