R6 - Steel Braided Brake Lines!!

Описание: BIG PROJECT FOR TODAY!! In today's video I go step by step on (How-To) replace your OEM rubber brake lines with fancy, good looking, colorful steel braided lines! I explain the PRO's of having steel braided lines over the OEM rubber hoses and I fully show the entire process from start to finish! This is a long video but If you need a step by step tutorial I think this video will work for you!

R6 Union Bolt/Banjo Bolt Torque Specs
Front Calipers - 24 ft/lbs
Front Master Cylinder - 24 ft/lbs
Rear Caliper - 24ft/lbs
Rear Master Cylinder - 24 ft/lbs

Steel Braided Brake Line Install Steps:
Step 1 - Remove brake fluid from the front
Step 2 - Remove brake fluid from the rear
Step 3 - Remove the front fender
Step 4 - Throw down some rags
Step 5 - Remove ABS sensor
Step 6 - Remove sensor line clips
Step 7 - Remove brake lines from the manifold
Step 8 - Remove mounting bolt
Step 9 - Remove manifold from bracket
Step 10 - Remove brake lines from calipers
Step 11 - Remove bolt from mount
Step 12 - Remove master brake line
Step 13 - Straighten out bracket
Step 14 - Install Three Way manifold
Step 15 - Install Left side brake line
Step 16 - Install Right side brake line
Step 17 - Tighten lines at the manifold
Step 18 - Tighten brake line going to manifold
Step 19 - Tighten union/banjo bolts
Step 20 - Double check fittings
Step 21 - Install master brake line
Step 22 - Install brake line mount
Step 23 - Check all fittings and bolts
Step 24 - Admire great work!
Step 25 - Install front fender
Step 26 - Move to the rear
Step 27 - Remove reservoir bracket
Step 28 - Remove EVERYTHING!
Step 29 - Remove the bracket
Step 30 - Hold off on this step, trust me!
Step 31 - Hold off on this step also!
Step 32 - Flatten the small flange
Step 33 - Install two manifolds together!
Step 34 - Tighten down input & output lines
Step 35 - Install small brake line
Step 36 - Tighten on both ends
Step 37 - Install long brake line
Step 38 - Attach wheel sensor line
Step 39 - Tighten both ends
Step 40 - Reinstall the reservoir bracket
Step 41 - Tighten Allen bolt and nut
DONE!!! Time to add brake Fluid!

Bleeding the Brake Line Steps:
Fill the reservoir almost to the top of the container
Step 1 - Place Vinyl line onto bleeder screw
Step 2 - Make sure bleeder screw is closed
Step 3 - Open the bleeder Screw
Step 4 - Push brake lever and close the bleeder screw
Step 5 - Release the lever, and open the bleeder screw once again
Step 6 - Push on the lever and close then bleeder screw
Step 7 - Repeat steps 2 to 6
Step 8 - Fluid level in the reservoir
Step 9 - Once you see some fluid, close the screw and move to the other front caliper
Step 10 - While doing this make sure you watch your reservoir and keep topping it off
Step 11 - Now that you have fluid at both front calipers, move onto the master cylinder
Step 12 - Repeat the process
Step 13 - Move back to left front caliper
Step 14 - Pump lever three times and hold, open the bleeder screw to allow fluid to flow
Step 15 - Move on to the master
Step 16 - Clean off bleeder screws
Step 17 - Refill the reservoir
Step 18 - Tie off levers

Hardware Left Over
1x Allen Bolt from OEM rear manifold
4x Crush Washers from the OEM Union/Banjo bolts from the rear
2x Union/Banjo bolts from the rear
1x Union/Banjo bolt from front master brake line
1x Union/Banjo bolt from front right side caliper
1x Union/Banjo bolt from front left side caliper
1x Allen Bolt from front OEM Manifold
6x Crush Washers from OEM Union/Banjo bolts from the front
5x OEM rubber brake lines which you removed

--------------------

FIND ME HERE!
✦Instagram -   / chrgitup  
✦YouTube -    / chrgitup  
✦Facebook -   / chrgitup  
✦Support the Channel on Patreon -   / chrgitup  

--------------------

CHRGITUP MERCH! YUUUUUP MERCH!!
✦TeeSpring -- https://teespring.com/stores/chrgitup...
✦Redbubble -- https://www.redbubble.com/shop/ap/673...

--------------------

USE MY REFERRAL CODES!

✦Damon Motorcycles
https://damon.com?from=Csaba&referrer...
✦Uber
https://partners.uber.com/join/?city=...
✦Camera Butter
https://camerabutter.com/?ref=chrgitup

--------------------

#R6 #BrakeLines #Spiegler

DISCLAIMER: Links in this video description might be affiliate links. If you purchase a product or service using one of these links, I may receive a small commission at no additional cost to you.