How to Assemble 3D Printed Big Bobber - Planeprint

Описание: This is a Big Bobber from PlanePrint. In this video I will show step by step how to assemble the fuselage and the wing. My next video will show how to install the electronics and get the plane ready for maiden flight.

If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...

Thank you so much to https://www.planeprint.com for sponsoring this build!

Thank you so much for watching!

How to Print Thin Wall:    • How to Print Thin Wall - Planeprint | Big ...  
Assemble Part 2:    • How to get your Big Bobber ready for the M...  
Full Maiden Flight:    • Big Bobber Maiden Flight - Planeprint  
Quick Full Build:    • 3D Printed Big Bobber Full Quick Build Vid...  

See what else I am working on: https://www.instagram.com/troymcmilla...
  / troymcmillan_rc  

#3Dprinted,#RCairplane, #ItFlies

Products Mentioned:
Big Bobber: https://www.planeprint.com/product-pa...
JGAurora A5S 3D Printer: https://amzn.to/3hn5cdN
JGMAKER MAGIC Printer: https://amzn.to/3nmonb6
Yellow PLA: https://amzn.to/30zsVRO
Black PLA: https://amzn.to/30E4YIT
TPU: https://amzn.to/2Sw3Oe8
Motor: https://amzn.to/3lliUj5
40amp ESC: https://amzn.to/3jD7qH5
12x4 Propeller: https://amzn.to/33xLAyZ
5mm Prop adaptor: https://amzn.to/34wM088
7x Servos: https://amzn.to/3jEI9fG
2700mah 3S Battery: https://amzn.to/34ttPjJ
AR620 Receiver: https://amzn.to/3j4PbK4
DX6 Transmitter: https://amzn.to/3l6NFsD
3pin wire assortment: https://amzn.to/3l1xNYt
XT60 connector: https://amzn.to/3iyZWnf
Y-Harness: https://amzn.to/3jAFwvo
Screw assortment: https://amzn.to/2SvMxSs
2mm push rod ends: https://amzn.to/3nnjD4U
Z-Bend pliers: https://amzn.to/34mA0rt
Hot knife: https://amzn.to/34AGOB1
Drill Bits: https://amzn.to/3nIJzrx
Carbon Rods: https://www.readymaderc.com




*These are the settings I used for my JGMaker Magic 3D Printer with eSun PLA. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!
Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 213
Build Plate Temperature – 60
Flow – 116
Enable Retraction – Checked
Retraction Distance – 5
Retraction Speed – 80
Retraction Extra Prime Amount – 0.9
Speed:
Print Speed – 100
Outer Wall Speed – 30
Inner Wall Speed – 30
Travel Speed – 80
Travel:
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 20
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle







Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!