Matek F765-WSE Flight Control Board

Описание: Matek F765-WSE Flight Control Board
F765-WSE Matek page - http://www.mateksys.com/?portfolio=f7...
F765-WSE Banggood - https://bit.ly/3Csie3X

FC Specifications (from Matek Product page)
MCU: STM32F765VIH6, 216MHz , 512KB RAM, 2MB Flash
IMU: ICM42688-P (SPI4)
Baro: DPS310 (I2C2)
OSD: AT7456E (SPI2)
Blackbox: MicroSD card slot (SDIO)
6.5x Uarts (1,2,3,Rx5,6,7,8) with built-in inversion.
1x Softserial1_Tx (INAV)
12x PWM outputs (S1~S10 support Dshot)
6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
2x I2C
1x CAN
USB/Beep Extender with Type-C(USB2.0)
Dual Camera Inputs switch
9V(12V) for VTX power switch
High-precision Current Sense, 220A range
ADC VB2 voltage divider: 1K:20K
ADC AirSpeed voltage divider: 20K:20K
Static power 160mA@5V

FC Firmware
INAV: MATEKF765SE
ArduPilot: MATEKF765SE

PDB
Input voltage range: 6.8~30V (2~6S LiPo)
1x ESC power pads
Battery Voltage divider 1K:20K (Scale 2100 in INAV, BATT_VOLT_MULT 21.0 in ArduPilot)
Current Senor: 220A, 3.3V ADC (Scale 150 in INAV, 66.7 A/V in ArduPilot)
Sense resistor: 90A continuous, 220A peak

BEC 5V output
Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
Continuous current: 2 Amps, Max.3A

BEC 9V /12V output
Designed for Video Transmitter, Camera, Gimbal ect.
Continuous current: 2 Amps, Max.3A
12V option with Jumper pad
for stable 9V/12V output, input voltage should be greater than output voltage +1V

BEC Vx output
Designed for Servos
Voltage adjustable, 5V Default, 6V or 7.2V via jumper
Continuous current: 8 Amps, Max.10A
for stable Vx output, input voltage should be greater than Vx voltage +1V

BEC 3.3V output
Designed for Baro / Compass module and external 3.3V peripherals
Linear Regulator
Continuous current: 200mA

Physical
Mounting: 25 x 25mm, Φ2mm
Dimensions: 44 x 29 x 14.5 mm
Weight: 22g w/ USB/buzzer adapter

Including
1x F765-WSE
1x USB(Type-C)/Beep (Passive buzzer) Extender
2x 20cm JST-GH-4P to JST-GH-4P cable for CAN & I2C port
1x 20cm JST-SH-6P to JST-SH-6P cable for USB extender.
1x Rubycon ZLH 35V 470uF capacitor
Dupont 2.54 pins (Board is shipped unsoldered)

Like, Subscribe & Ding the 🔔 - http://bit.ly/ANsubscribe

🔎 More information 🔍
► Newton Airlines Uncut - http://bit.ly/NewtonAirlinesUncut
► Newton Airlines blog - http://newtonairlines.blogspot.com.au
► Links for my build materials - http://newtonairlines.blogspot.com/20...
► Andrew Newton YouTube -    / andrewnewtonaustralia  
► My portal - http://anewton.net
► My Thingiverse - https://www.thingiverse.com/andrewrcn...
► iNav Basics and FAQs - https://newtonairlines.blogspot.com/s...
► All my iNav CLI Dump files - http://bit.ly/2t2OPz7
► Depron Armin Wing build -    • Depron wing build  
► Skyshark P4X spars - https://www.kitesandfunthings.com/Pro...
► GBC EZLOAD laminating film (May be discontinued) - https://shop.quadient.com.au/products...
► Alternative 75 micron laminating film (not tried by me) - https://www.boundtoimpress.com.au/sho...
► Depron and foam board - My 6mm and 3mm depron came from www.tradewarehouse.com.au But from 2020 it seems they no longer sell proper depron. I have not found another supplier yet.

👌🏽Support this channel 👌🏽
This is a fun hobby for me, not a money making venture.
I don't have a Patreon account, and choose the minimum possible advertising option.
However if you would like to support this channel here are some options
►Direct donations to Paypal.Me - https://paypal.me/apnewton
►Small donations via BuyMeACoffee - https://www.buymeacoffee.com/AndrewPN...
►Affiliate links - BANGGOOD RC - https://bit.ly/3mMnJ93
If you use the affiliate link to make a purchase I may receive a commission at no extra cost to you.

👀 No single review will tell the whole story. Be clever, watch other reviews and shop around before making any purchase.

#AndrewNewton #MatekF765WSE #INAV