How to replace the Upper Control Arms 2014 - 2019 Chevrolet Silverado 🚗

Описание: Find the parts used in the video on CarParts.com just there https://carparts.solutions/SILVERADO
Over 1 million auto parts at your fingertips, download our app 🤖 https://carparts.solutions/AppGooglePlay or 🍎 https://carparts.solutions/AppIOS

⚙️ NEEDED CARPARTS AND PRODUCTS
Upper control arms : https://carparts.solutions/UpperContr... and https://carparts.solutions/UpperContr...

Struts : https://carparts.solutions/Struts_SIL...

Penetrating oil : https://carparts.solutions/Penetratin...

Silicone grease

💪 TIGHTENING TORQUES
Strut foot bolts: 37 Ft-Lbs

Strut 3 upper mount nuts : 37 Ft-Lbs

Upper control arm ball joint nut : 37 Ft-lbs + 100 degrees

Camber bolts : 140 Ft-Lbs

🛠 TOOLS
The toolbox recommended by CARPARTS.COM to repair your Chevrolet Silverado :
https://carparts.solutions/ToolBox

List of the tools we used to replace the upper control arms on a Chevrolet Silverado :
Measuring tape
Hydraulic jack : https://carparts.solutions/FloorJack
Jack stands : https://carparts.solutions/JackStands
Wheel lug wrench
Wire brush
Marker
Fork
Ratchet
10mm socket
17mm wrench
Ball joint puller
Hammer
Plastic mallet
17mm socket
Extender
18mm socket
Crowbar
21mm socket
21mm wrench
Flat head screwdriver
16mm socket
Torque wrench :
20 to 250 Ft-lbs https://carparts.solutions/TorqueWren...
100 to 600 Ft-lbs https://carparts.solutions/TorqueWren...

Don't forget to subscribe :    / @carpartscomofficial  

🛻 COMPATIBLE VEHICLES
The operation and tools displayed in the video should be available on the following vehicles :
2014 Chevrolet Silverado
2015 Chevrolet Silverado
2016 Chevrolet Silverado
2017 Chevrolet Silverado
2018 Chevrolet Silverado
2019 Chevrolet Silverado

📽 🛠 USEFUL VIDEOS 🛠 📽
How to jack your Chevrolet Silverado safely :    • How to jack your 2014 - 2019 Chevrolet Sil...  

⚠️ CARPARTS.COM'S INFOS
Before lifting your vehicle, it is necessary to measure the distance between the centre of your wheel and the wheel arch. This will allow you to achieve an optimal tightening of the silentblock equipped elements in their initial position.

To avoid damaging the bushings, tighten the upper arm control and strut holding bolts in the “vehicle on the ground” position.

During this operation, you will be intervening on the front axle of your car, so it is advisable to perform a wheel alignment afterwards.

🚨 DISCLAIMER
This video is for entertainment purposes only. Carparts.com, Inc. disclaims all damages including, but not limited to, actual, consequential, and/or punitive, for any liability, claim, or any other injury or cause related to or arising from any information or lack thereof posted in this video. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All mechanical car projects entail some risk. It is the sole responsibility of the viewer to assume this risk. If you are in doubt, please consult a licensed mechanic in your area.

📚 CHAPTERS
0:00 Intro
0:12 Measure the distance between the center of your wheel and the wheel arch
0:22 What is a camber bolt ?
0:52 Remove the brake hose and the ABS sensor
1:33 Remove the control arm ball joint
2:10 Remove the strut
3:25 Remove the upper control arm holding bolts
3:43 Remove the control arm
3:54 Prepare the installation
4:15 Install the upper control arm holding bolts
4:48 Screw the upper control arm holding bolts back
5:15 Put the strut back
6:07 Put the control arm ball joint into the wheel knuckle
6:26 Tighten the nuts and bolts + tightening torque
8:00 Put the brake hose and the ABS sensor back
8:33 Put your Silverado back on the ground + saftey tips