Create A Wireless Network Using AccessPoint and End Devices-Cybersecurity-2026 (By Dan Hyper)🚀

Описание: Learn the essentials of Wireless Networking in Cybersecurity, from the Device model basics to creating your own Network! 🚀 This guide is perfect for beginners or newbies, and aspiring security professionals.

In the Third Episode of our Journey, you'll be shown a View of a Network Setup (LAN) with AccessPoint, PC, Laptop, SmartPhone and Server, and also step-by-step process to create yours.


Here is the PDF Guide used: https://drive.google.com/file/d/1fXea...

(I just underwent a verification process, the google-drive link should be clickable soon)

Alternative Guide:
Step 1: Add Devices.
Drag and Drop: AccessPoint, PC, Laptop and Smartphone

Step 2: We set up the AccessPoint Device by:
Click on device - Check the Physical Tab - Check the power status
Step 2B: We Configure our Accesspoint Device
Go to Config tab - Click on Port 1 - Edit SSID name to remember. Then under
Authentication, Select “WPA2-PSK” - Edit the Passphrase/Secure password to
remember - Close the tab.
Note: SSID – Wifi-name. [Remember its values]
SSID stands for Service Set Identifier.
It is simply the publicly broadcast name of a wireless network—what you see in the list
when you look for Wi-Fi networks on your phone or laptop
(e.g., Home_WiFi , Office_AP , or in Packet Tracer, default ).
The SSID acts like a label for the specific network signal the Access Point is putting out.

Step 3: Configure PC
Go to Physical tab - Click the physical hardware button to turn OFF PC - Scroll
down to see exactly the same image on PC-port at the button right-corner - By
Dragging, Remove default image/module from hardware and add to “MODULES”
list - Then Drag “WPM300N” from list to the hardware slot to install/insert. Now,
turn ON PC.
Step 3b: Click on PC - Desktop - Set IP Address: 192.168.1.1
Step 3c: Click on PC - Config - Set the Initial “AccessPoint” values in the fields.
Set SSID - Click WPA2-PSK - Set Values. [Ensure port is ON]
Step 3d: [*Skipped] Now, to test connection to Accesspoint, Click Desktop - PC Wireless -
Enter SSID and Passkey/Password. Then click connect. Wait for “Success
message.”

Step 4: Go to Physical tab - Click the physical hardware button to turn OFF
Laptop - Scroll down to see exactly the same image on Laptop-port at the button
right-corner - By Dragging, Remove default image/module from hardware and
add to “MODULES” list - Then Drag “WPC300N” from list to the hardware slot to
install/insert. Now, turn ON Laptop.
Step 4b: Click on Laptop - Desktop - Set IP Address: 192.168.1.2 (Ensure IP
Range: 192.168.x.x with the PC)
Step 4c: Click on laptop - Config - Set the Initial “AccessPoint” values in the
fields.
Set SSID - Click WPA2-PSK - Set Values. [Ensure port is ON]
Step 4d: [*Skipped] Now, to test connection to Accesspoint, Click Desktop - PC Wireless -
Enter SSID and Passkey/Password. Then click connect. Wait for “Success
message.”

Step 5: Click on Smartphone - Desktop - Set Ip Address: 192.168.1.3
5b: Click on Config tab - Set the Initial “AccessPoint” values in the fields.
Set SSID - Click WPA2-PSK - Set Values. [Ensure port is ON]

Step 6: Now, check to confirm connectivity by “Radio signals” transfer.
Step 7: PING and Test Connectivity using Simple PDU.

That's it - You good to GOo👨‍💻⚡


#WirelessNetworking #NetworkingInCybersecurity #BuildANetwork #TestNetwork #NetworkingInCybersecurity #CybersecurityTutorial #NetworkSecurity #OSIModel #TechExplained #CiscoPacketTracer #PDFGuideOnNetworking #WirelessNetworkGuide