Gun Cleaning 101: How to Clean the CZ P-10 F Competition Ready Pistol

Описание: In this video we demonstrate how to clean the CZ P-10 F Competition Ready pistol using the Otis Technology 3 Step Cleaning Process with Memory Flex cable, patches and Shooter's Choice FP-10 CLP Lubricant Elite.

Products used in this video
Otis Professional Pistol Cleaning Kit: https://otistec.com/professional-pist...
Otis AP Brush: https://otistec.com/3-pack-ap-brushes...
Shooter's Choice FP-10 CLP: https://otistec.com/shooters-choice-f...
Otis Microfiber Cloth: https://otistec.com/microfiber-gun-cl...

How to tie and Otis gun cleaning patch video:    • How To Tie An Otis Patch  
Otis 3-Step Cleaning Process video:    • The Otis 3-Step Gun Cleaning Method  

Otis products include a No-Nonsense Warranty and are manufactured in Lyons Falls, NY, USA
Breech-to-Muzzle® is a Registered Trademark of Otis Technology
We are #AmericasGunCare

►CHECK US OUT!
Facebook:   / otistechnology  
Instagram: www.instagram.com/otistechnology
Website: https://otistec.com/
Rumble: https://rumble.com/user/otistechnology
Juxxi/Full30: https://www.full30.com/channel/otiste...


CZ-USA's recommended gun cleaning procedure from their owners manual:

CLEANING THE PISTOL
When to clean the pistol:
• As soon as possible after each use •
If the firearm gets wet • At least once a year in a temperate climate
• As often as once a month in a tropical climate, or other demanding environment

Cleaning the Barrel Bore and the Cartridge Chamber
If the pistol has not been fired or if only a few cartridges have been fired, clean the barrel bore and cartridge chamber with a clean patch attached to the cleaning rod. Repeat the cleaning, changing patches, until the last patch comes out clean. When the barrel bore is very dirty, apply a quality firearms CLP (Cleaner, Lubricant, Protectant) using a cleaning brush. Let the solvent act for about 10 minutes (this time may vary depending on the degree of fouling). Then thoroughly scrub out the barrel bore. Subsequently, dry the barrel bore and cartridge chamber with a clean patch and check that all powder residues or fouling have been removed. If necessary repeat this procedure. The cleaning rod and the brush must be inserted into the barrel bore from the chamber, to prevent wear or damage to the muzzle. Pass the brush all the way through the barrel bore before reversing the movement. If you change directions with the brush in the barrel, the brush could stick.

Cleaning of Other Pistol Parts
Other parts of the pistol (including the external surfaces of the barrel) should be cleaned with a cleaning brush and a dry cloth. A quality CLP can be used for proper cleaning. Never use an agent specifically designed for barrel bore cleaning! These solutions could remain in the joints, and after some time could cause corrosion. Check that cloth particles or brush bristles have not become lodged in any part of the pistol.

Preserving
When the barrel’s bore, chamber, and all other accessible parts of the firearm are clean and dry, apply a thin film of CLP via a cloth. Place several drops of oil: • Around the exterior of the barrel 1/4” back from the muzzle • At the locking surface where the front of the barrel hood locks into the slide when the firearm is in battery (above the chamber on the barrel) • On each of the rails within the frame, located on the frame inserts Remove all excess oil from the exterior of the firearm. Before shooting, always wipe the barrel bore dry. For use in extremely low temperatures, remove the oil from all accessible parts of the firearm or apply a lubricant prepared especially for these conditions. The application of thick preserving agents such as grease should only occur for long-term storage in demanding climate environments, and before any use of the pistol it must be thoroughly removed from all parts of the firearm.