How-To: Bleeding the LT4 Supercharger // Camaro ZL1 & ZL1 1LE

Описание: In this “How-To:” video I take a look at the process to bleed the air out of the LT4 Supercharger’s cooling system found in the Camaro ZL1 & ZL1 1LE. Special shout out to Anthony B. for helping answer many of my questions!

Buy the Modified LT4 Coolant Pump Relay Here:
https://followmyline-shop.fourthwall....

Dedicated Motorsports LT4 SC Coolant Filler Adapter Tool:
https://bit.ly/lt4scadptr

Affiliate Links:
Fused Jumper Wire w/ 15 Amp Fuse:
https://amzn.to/3PDi4Ph

14AWG Male Spades:
https://amzn.to/3Sfr3Jo

Mini Funnel Kit:
https://amzn.to/3ZJurOA

Genuine GM Dex-Cool Coolant 12378390:
https://amzn.to/3FTX6XS

Prestone Dex-Cool Coolant:
https://amzn.to/47qUMDz

Redline Water Wetter:
https://amzn.to/3tmYWxD

Distilled Water:
https://amzn.to/48zHjuw

Alternative Water Bottle to 2-Liter Soda Bottle:
https://amzn.to/3LJgiea

Scott’s Blue Shop Towels:
https://amzn.to/3FiPoXj

Generic Shop Rags:
https://amzn.to/3EYHmT3

Other Items I Use:
Milwaukee 1/2” Drive Socket & Wrench Set:
https://amzn.to/430BKlz

Milwaukee 3/8” & 1/4” Drive Socket & Wrench Set:
https://amzn.to/3Mztv98

Milwaukee M12 3/8” Ratchet:
https://amzn.to/3Ezznvo

1/4" Drive Torque Wrench - Inch Pounds:
https://amzn.to/48gfiIs

Torx Bit Set:
https://amzn.to/3ZkOGlw

Magnetic Pickup & Tray Tool Set:
https://amzn.to/3P6sJlv

LED Side Markers:
https://amzn.to/42RBzJ2

Lift Pads:
https://amzn.to/3s3FwtT

ZL1 Addons Premium Magpuck:
https://tinyurl.com/bd9kp5cm

Rotofab CAI for Camaro w/ LT4 V8:
https://amzn.to/43jSmW8

Rotofab CAI for Camaro w/ LT1 V8:
https://amzn.to/3ZRchbT

Corsa Extreme Axle Back Camaro V8:
https://amzn.to/3BSxdG3

Corsa Carbon Fiber CAI for ZL1:
https://tinyurl.com/wr8s4rx8

Chapters:
0:00 - Intro // Overview on How To Bleed the System
0:32 - Tools Needed // Links in Description
3:05 - Checking the Engine Coolant System // Main Reservoir & Surge Tank
4:20 - Location of Fuse Block
4:47 - Location of K6 Coolant Pump Relay
5:17 - Where to Plug in the Fused Jumper Wire
5:28 - Using a Modified Relay
5:48 - Important // Don't Run Pump for More Than 5 Minutes at a Time
6:40 - Getting the DMS Adapter On // Location of Bleeder Valve
9:30 - Closeup of Air Bubbles
10:13 - Top View of Air Bubbles
10:23 - Air Burp // Removing Relay/Jumper Wire
10:50 - Squeezing the Rubber Hoses // Supercharger Cooling System
11:27 - Audio Clip of Coolant Pump Running // Turning Off
12:19 - Removing Relay/Jumper Wire // Removing DMS Adapter
13:18 - Wipe Up/Soak Up Residual Coolant in the Bleeder Valve // Remove O-Ring
14:08 - Place OEM Relay Back Into Fuse Block
14:34 - Wrap Up // Outro

These are affiliate links to the products. I make a small commission on anything purchased from my links.

**Disclaimer:
Due to factors beyond my control, I cannot guarantee against improper use of the information I share in my videos. (FollowMyLine17) assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not (FollowMyLine17) or any business affiliated to (FollowMyLine17).**

Special Shout Out to My Son's YouTube Channel:
   • My first ever video!!!