ycliper

Популярное

Музыка Кино и Анимация Автомобили Животные Спорт Путешествия Игры Юмор

Интересные видео

2025 Сериалы Трейлеры Новости Как сделать Видеоуроки Diy своими руками

Топ запросов

смотреть а4 schoolboy runaway турецкий сериал смотреть мультфильмы эдисон
Скачать

Soldering Iron Vs Hot Air Station to remove through hole technology component from PCB

Автор: Tzirf

Загружено: 2024-10-29

Просмотров: 1167

Описание: This video shows the difference between using a soldering iron and hot air station to remove a component (in this case a ROM Chip) that uses through hole technology, often referred to as THT. The entire purpose of this video is to show that this can be done using an inexpensive soldering iron in the $30-$60 dollar range and some solder wick and flux. Additionally I show the same process using a hot air station to demonstrate the difference in the time required to remove the same component. The reason I chose to do this video is because I often am asked if someone can do repairs that I do with only a soldering iron and the answer to this is yes there are many scenarios where a soldering iron is all that is needed. This video demonstrates what can be achieved with enough effort using a soldering iron. It also demonstrates why a hot air station is preferred for many repairs as its far more efficient at removing certain components from a PCB.

Although I chose to showcase this on an older electronic with larger components the same technique can be used on many electronics even newer ones to remove certain components using only a soldering iron. Keep in mind that certain surface mounted component this will never work on because the solder pads/legs are underneath the component and its not possible to heat them with the soldering iron. These components require hot tweezers or a hot air station.

My original post for this can be found at https://www.tzirf.com/general-discuss...

For additional resources & guides you can visit my website https://www.tzirf.com. It is a forum based website where I post all the repairs I am working on so that the resources are there for others. If you are working on a repair and want to share it, or need help with your repair I encourage you to join and make a post.

Timestamps

0:01 Intro (What this video is about and why I decided to do it)
2:12 Using Soldering Iron to remove THT Component
4:12 Lets use a clamp to hold the PCB
9:50 Removing solder on front side of PCB
14:26 testing pins to verify if they are desoldered
24:34 Inspecting with Microscope to check which pins are still soldered in place
26:34 Removing solder with solder wick from pin under microscope
28:10 Lets see if the chip will separate from the PCB
29:53 setting up to use hot air station to remove THT component
32:15 removing THT chip with hot air
33:08 Outro + Conclusion

Music I use: https://www.bensound.com
License code: QU7QZJ99SHEGINZU

Не удается загрузить Youtube-плеер. Проверьте блокировку Youtube в вашей сети.
Повторяем попытку...
Soldering Iron Vs Hot Air Station to remove through hole technology component from PCB

Поделиться в:

Доступные форматы для скачивания:

Скачать видео

  • Информация по загрузке:

Скачать аудио

Похожие видео

Как использовать термовоздушную паяльную станцию ​​/ Пайка / Электроника

Как использовать термовоздушную паяльную станцию ​​/ Пайка / Электроника

Легкое распайка — удивительный трюк || Учебное пособие по пайке

Легкое распайка — удивительный трюк || Учебное пособие по пайке

Rapid Fast Soldering Iron - Kaiweets KETSO2

Rapid Fast Soldering Iron - Kaiweets KETSO2

EEVblog #437 - Removing SMD Parts with ChipQuik

EEVblog #437 - Removing SMD Parts with ChipQuik

Peacock XT Computer -  Mainboard Repair

Peacock XT Computer - Mainboard Repair

Чем ОПАСЕН МАХ? Разбор приложения специалистом по кибер безопасности

Чем ОПАСЕН МАХ? Разбор приложения специалистом по кибер безопасности

Sega Game Gear Repair & Restore - This turned out way better than expected

Sega Game Gear Repair & Restore - This turned out way better than expected

Not All Hot Air Stations Are Same!

Not All Hot Air Stations Are Same!

Andonstar-- Ep.9 How to clean the flux residue after soldering?|PCBs Flux Cleanup with alcohol

Andonstar-- Ep.9 How to clean the flux residue after soldering?|PCBs Flux Cleanup with alcohol

Как транзисторы считают? Логика, из которой сделаны процессоры. Понятное объяснение!

Как транзисторы считают? Логика, из которой сделаны процессоры. Понятное объяснение!

Dynaco CDV Pro CD player with vacuum tubes - let the torture begin

Dynaco CDV Pro CD player with vacuum tubes - let the torture begin

How to clean and re tin your soldering iron

How to clean and re tin your soldering iron

Интернет через Dial-up без АТС

Интернет через Dial-up без АТС

Почему на конденсаторе такая метка? Вот почему!

Почему на конденсаторе такая метка? Вот почему!

Что такое Туннельный диод и как он работает.

Что такое Туннельный диод и как он работает.

How to solder components using hot air without them blowing away

How to solder components using hot air without them blowing away

Внутренняя красота пассивных электронных компонентов: 3D Анимация (CGI) устройство радиодеталей

Внутренняя красота пассивных электронных компонентов: 3D Анимация (CGI) устройство радиодеталей

UC3842, косой мост и расширение прямого такта более 50%.

UC3842, косой мост и расширение прямого такта более 50%.

How to Solder a Pico Defuse into a Wii U Tutorial

How to Solder a Pico Defuse into a Wii U Tutorial

Desoldering Large DIP/Through Hole Chips with a Cheap Heat Gun

Desoldering Large DIP/Through Hole Chips with a Cheap Heat Gun

© 2025 ycliper. Все права защищены.



  • Контакты
  • О нас
  • Политика конфиденциальности



Контакты для правообладателей: [email protected]